Peugeot 208 Key Replacement
Peugeot 208 key replacement is best left to experienced auto locksmiths with the right equipment and technical knowledge. They can design and program keys faster and less expensive than dealerships.
If the key fob has stopped locking or unlocking your doors it could be due to a dead coin battery. There are also other reasons that the key might be malfunctioning.
Dead Coin Battery
A dead coin battery will hinder your Peugeot 208 from locking or unlocking, and will not start the engine. In this scenario you'll need make use of the alternative method for starting as described in your vehicle's owner's manual.
The spark plugs may also be worn out. The spark plugs light the fuel to start the engine. However, they have a limited lifespan. If peugeot 308 key replacement are not used enough to last, they'll eventually fail.
There is an easy solution to this issue. The best option is to determine the voltage of your car battery using a multimeter. If it's less than 11.5 Volts, then you need to replace it. It is also important to clean the contacts of the battery in the event that it is damaged by corrosion. This can be done by removing the rubber covers off the two terminals on the battery and then using a wirebrush, you can remove any parts of the battery that are corroded. Then, reconnect the positive pole cables to the negative.
Water Damage
If your 208 won't start and the battery hasn't failed, you should inspect the spark plugs. You might find that they're filthy and don't spark. This can be easily corrected by cleaning the spark plugs in an workshop.
Peugeot cars use a key with a transponder compatible with the immobiliser. This ensures that only the right key can turn the engine. If the chip in the Peugeot key is damaged then it won't send the correct signal to the vehicle.
This is a common problem that is often caused by water damage. This is most common in colder climates, as the vehicle might have been exposed to snow or rain. If this is the case, contact a reputable auto locksmith who will have all the tools and equipment needed to change the key's programming. They will also have all the latest technology and machinery required to create the Peugeot smart key. The process should not take more than 15 minutes.
Contacts for the battery that are defective
Peugeot replaced the old transponder chips by introducing a new model that utilizes electronic components that are mounted on a circuit board. The new system is fantastic in its initial state, but the circuit boards begin to degrade with time and stop working properly.
This could prevent the immobiliser chip from activating the immobiliser chip, causing your car not to start. If this happens, it's recommended to call a Peugeot specialist or locksmith.
A common issue occurs when the battery in the key fob begins to fail. This causes the blade of the key to stop feeding into your lock. A locksmith for cars can replace the battery and cut a fresh blade for you, it's generally a quick fix.
Faulty Receiver Module
It could be that the receiver module has a problem If your Peugeot key fob stops working after being dropped on the floor, or exposed to a sudden downpour or accidentally washed. The receiver module is responsible for transmitting radio frequency to the onboard computer which controls the central locking system of your Peugeot vehicle.
The key fob itself has rubber seals which prevent water from getting to the electronic chip inside. However prolonged exposure to water can cause damage to these seals and the chip. Submerging the key fob into ocean water at the beach or throwing it into the water can be especially damaging because of the high salt content.
The module will have to be replaced if the Peugeot spare key no longer works. This is only completed by an experienced auto locksmith or Peugeot specialist. Peugeot keys like other cars are secured by an immobilizer device. This requires the right code to begin the car. It is for this reason that you should only trust a Peugeot locksmith to create and program an alternative.
Computers with faulty on-board computers
The computer on board in your Peugeot is responsible for a variety of the systems within the car, from power windows to the airbags. The on-board computer will display an error code when something goes wrong. This code is stored in the system and will stay there until the problem is fixed. This may require the on-board computers to be replaced.
One of the most common causes of the airbag light flashing is loose or corroded connections in the airbag sensor. This could be due to wear and tear, ageing, or exposure to moisture and salt. It is important to have this issue addressed as soon as you can, since an airbag that is malfunctioning can be dangerous in the event of an accident.
If your Peugeot is showing a card that is not being detected error, then the key battery inside the key fob may be dead or weak. This could prevent the key fob from sending a signal to disable the standard immobilizer in your vehicle. Test this by pressing the unlock key on the fob's key, then trying to start your vehicle. If it doesn't work it is because the battery of the key needs to be replaced.